• Part Number: P01120306
• Current : 1,000 A
• Ratio : 1000 / 5
• Output : 5 mA / A
• Output signal: alternating current
• Transformation ratio: 1,000/5
• Output via isolated Ø 4 mm female sockets
• Output protected against voltage surges

• ELECTRICAL SPECIFICATIONS: 
• Current range: 1 A AC .. 1,200 A AC
• Current transformation ratio: 1000:5
• Output signal: 5 mA AC / A AC (5 A for 1,000 A)
• Accuracy and phase shift (1):
• Primary current: 1 A .. 20 A,  20 A,  50 A (2), 200 A (2),  1,000 A (2), 1,200 A (2)
  
• Accuracy: en % ≤ 6 % + 0.5 mA,  ≤ 5 %,  ≤ 3 %,  ≤ 1.5 %,  ≤ 1 %, ≤ 1 %
• Phase shift: not specified, ≤ 3°,  ≤ 3°,  ≤ 1.5°,  ≤ 1°,  ≤ 1°
• Bandwidth: 30 Hz .. 10 kHz
  
• Crest factor: ≤ 6 for a current ≤ 3,000 A peak (500 ARMS)
• Maximum currents: 1,000 A continuous for a frequency ≤ 1 kHz (limitation proportional to the inverse of frequency beyond) 1,200 A for 30 minutes max (interval between measurements > 15 minutes)
• Load impedance: ≤ 0.6 Ω
• Impedance of connection leads: ≤ 40 mΩ
• Maximum output voltage (secondary open): Electronic protection circuit limiting voltage to 30 V peak max
• Operating voltage: 600 VRMS
• Common mode voltage: 600 V category III and pollution degree 2
• Influence of adjacent conductor: ≤ 1 mA / A at 50 Hz
• Influence of conductor position in jaws: ≤ 0.2 % of output signal for frequencies ≤ 400 Hz
• Load influence: From 0.2 Ω to 0.6 Ω; < 0.5 % on measurement; < 0.5 ° on phase
• Influence of frequency (3): < 1 % of output signal from 30 Hz .. 48 Hz; < 0.5 % of output signal from 65 Hz .. 1 kHz; < 1 % of output signal from 1 kHz .. 5 kHz
• Influence of crest factor: < 1 % of output signal for crest factor ≤ 6 with current; ≤ 3,000 A peak (500 ARMS)
  
• Influence of DC current superimposed on rated current: < 1 % of output signal for a current ≤ 30 A DC
• MECHANICAL SPECIFICATIONS: 
  
• Operating temperature: -10 °C to +50 °C
• Storage temperature: -40 °C to +70 °C
• Infl uence of temperature: ≤ 0.1 % of output signal per 10 °K
• Relative humidity for operation: 0 to 85 % RH with a linear decrease above 35 °C
• Influence of relative humidity: < 0.2 % of output signal from 10 % to 85 % RH
• Operating altitude: 0 to 2,000 m
• Max. jaw opening: 53 mm Patented progressive opening system
• Clamping capacity: Cable: Ø max 52 mm; Busbar: 1 busbar of 50 x 5 mm / 4 busbars of 30 x 5 mm
• Casing protection rating: IP40 (IEC 529)
• Drop test: 1 m (IEC 68-2-32)
• Shock resistance: 100 g (IEC 68-2-27)
  
• Vibration resistance: 5/15 Hz 1.5 mm; 15/25 Hz 1 mm; 25/55 Hz 0.25 mm (IEC 68-2-6)
• Self-extinguishing capability: Casing and jaws: UL94 V0
• Dimensions: 216 x 111 x 45 mm
• Weight: 550 g
• Colours: Dark grey case with red jaws
• Output: Safety sockets (4 mm)
• SAFETY SPECIFICATIONS: 
• Electrical safety: Instrument with double insulation or reinforced insulation between the primary the secondary and the grippable part located under the guard as per IEC 1010-1 & IEC 1010-2-032
• 600 V category III, pollution degree 2
• 300 V category IV, pollution degree 2
• Electromagnetic compatibility (EMC): EN 50081-1: class B; EN 50082-2:
• Electrostatic discharge: IEC 1000-4-2
• Radiated field: IEC 1000-4-3
• Fast transients: IEC 1000-4-4
• Magnetic field at 50/60 Hz: IEC 1000-4-8
• (1) Conditions of reference: 23 °C ± 3 °K, 20 % to 75 % RH, signal sinus, frequency of 48 Hz to 65 Hz, distortion factor < 1 %, no DC components, external magnetic fi eld < 40 A/m, no AC magnetic field, conductor centred for measurement, load impedance 0.2 Ω (5 VA)
• (2) Accuracy class in accordance with IEC 185: 5 VA - class 1 - 48 .. 65 Hz
• (3) Out of reference domain

• (1) C122 - Current Clamp Adapter
  
• (1) Instruction Manual

Brochure/Datasheet

Instruction Manual

Download

Note: Prices are not binding at any time subject to change without prior notice