• Part Number: P01120316
• Current : 1,000 A
• Output : 1 mV / A
• Output signal: alternating voltage
• Output / input ratio: 1 mV / A AC
• Output via isolated Ø 4 mm female sockets

• ELECTRICAL SPECIFICATIONS:
• Current range: 0.001 A AC .. 1,200 A AC
• Output signal: 1 mV AC / A AC (1 V for 1,000 A)
• Accuracy and phase shift (1):
• Primary current: 1 mA .. 100 mA,  0.1 A .. 1 A,  1 A .. 10 A,  10 A .. 100 A,  100 A .. 1,200 A
• % Accuracy of output signal ≤ 3 % + 5 µA,  ≤ 2 % + 3 µA,  ≤ 1 %,  ≤ 0.5 %,  ≤ 0.3 %
• Phase shift: not specified,  not specified, ≤ 2°,  ≤ 1°,  ≤ 0.7°
• Bandwidth: 30 Hz .. 10 kHz
• Crest factor: ≤ 6 for a current ≤ 2,000 A peak (300 ARMS)
• Maximum currents: 1,000 A continuous for a frequency ≤ 1 kHz (limitation proportional to the inverse of frequency beyond) 1,200 A for 40 minutes max (interval between measurements > 20 minutes)
• Output impedance: 1 Ω ± 1 %
• Load impedance: ≥ 1 MΩ and ≤ 100 pF
• Operating voltage: 600 VRMS
• Common mode voltage: 600 V category III and pollution degree 2
• Influence of adjacent conductor: ≤ 0.5 mA / A at 50 Hz
• Influence of conductor position in jaws: ≤ 0.1 % of output signal for frequencies ≤ 400 Hz
• Load influence: On receiver, for an input impedance of 100  Ω: ≤ 1 % on measurement, no measurement on phase. On receiver, for an input impedance of 1  kΩ: ≤  0.1 % on measurement, no measurement on phase.
• Influence of frequency (2): < 0.5 % of output signal from 30 Hz .. 48 Hz; < 1 % of output signal from 65 Hz .. 1 kHz; < 2 % of output signal from 1 kHz .. 5 kHz;
• Influence of crest factor: <  1 % of output signal for crest factor ≤  6 with current ≤ 2,000 A peak
• Influence of DC current superimposed on rated current: < 1 % of output signal for a current ≤ 15 A DC
• MECHANICAL SPECIFICATIONS:
• Operating temperature: -10 °C to +50 °C
• Storage temperature: 40 °C to +70 °C
• Influence of temperature: ≤ 0.2 % of output signal per 10 °K
• Relative humidity for operation: 0 to 85 % RH decreasing linearly above 35 °C
• Influence of relative humidity: < 0.1 % of output signal from 10 % to 85 % RH
• Operating altitude: 0 to 2,000 m
• Max. jaw opening: 53 mm Patented progressive opening system
• Clamping capacity: Cable: Ø max 52 mm
• Busbar: 1 busbar of 50 x 5 mm / 4 busbars of 30 x 5 mm
• Casing protection rating: IP40 (IEC 529)
• Drop test: 1 m (IEC 68-2-32)
• Shock resistance: 100 g (IEC 68-2-27)
• Vibration resistance: 5/15 Hz 1.5 mm; 15/25 Hz 1 mm; 25/55 Hz 0.25 mm (IEC 68-2-6)
• Self-extinguishing capability: Casing and jaws: UL94 V0
• Dimensions: 216 x 111 x 45 mm
• Weight: 550 g
• Colours: Dark grey case with red jaws
• Output: C116: Safety sockets (4 mm); C117: two-wire cable with reinforced insulation or double insulation, length 1.5 m, terminated by 2 insulated elbowed male banana plugs, Ø 4 mm
• SAFETY SPECIFICATIONS: 
  
• Electrical safety: Instrument with double insulation or reinforced insulation between the primary the secondary and the grippable part located under the guard as per IEC 1010-1 & IEC 1010-2-032
• 600 V category III, pollution degree 2
• 300 V category IV, pollution degree 2
• Electromagnetic compatibility (EMC): EN 50081-1: class B; EN 50082-2:
• Electrostatic discharge: IEC 1000-4-2
• Radiated field: IEC 1000-4-3
• Fast transients: IEC 1000-4-4
• Magnetic field at 50/60 Hz: IEC 1000-4-8
• (1) Conditions of reference: 23 °C ± 3 °K, 20 % to 75 % RH, signal sinus, frequency of 48 Hz to 65 Hz, distortion factor < 1 %, no DC components, external magnetic fi eld < 40 A/m, no AC magnetic field, conductor centred for measurement, load impedance ≥ 1 MΩ and ≤ 100 pF
• (2) Out of reference domain

• (1) C116 - Current Clamp Adapter
  
• (1) Instruction Manual

Brochure/Datasheet

Instruction Manual

Download

Note: Prices are not binding at any time subject to change without prior notice