• Part Number: 4034-220V
• Repetition rate of 0.1 Hz to 50 MHz
• Both channels offer full functionality and all parameters such as pulse width and transition time can be set independently
• Synchronize both channels with the push of a button
• Flexible trigger modes: Continuous, Triggered (internal, external, manual), Gated Burst and External Width
• Pulse width programmable from 10 ns to 10 s
• Transition times (rise and fall ) variable from 6 ns to 25 ms
• Programmable delay and double pulse
• Store up to 99 different test setups with auto retention of last power down setup
• 10 Vpp into 50 ohm output
• Closed case calibration
• Programmable via GPIB and RS-232
• SCPI compatible
• Applications:
• Automatic Test Equipment (ATE)
• Avionics and radar testing
• Switching power supply testing
• Characterization of active components

• CHANNELS: 2 
• FREQUENCY: 0.1 Hz to 50 MHz
• TIMING CHARACTERISTICS:
• PERIOD:
• Range (single pulse): 20 ns to 10 s (50 MHz to 0.1 Hz repetition rate)
• Range (doublepulse): 40 ns to 10 s (25 MHz to 0.1 Hz repetition rate)
• Resolution: Up to 6 digits, limited to 100 ps
• Accuracy: ±0.01 %
• Jitter: < 0.01 % of setting +20 ps on Period, Width and Delay
• WIDTH:
• Range 10 ns to (Period – 10 ns)
• Resolution Up to 6 digits, limited to 100 ps
• Accuracy ±(0.5% of setting +500 ps)
• Double Pulse ±(0.5% of setting +3 ns) for the second pulse
• DELAY:
• Range 0 ns to (Period – Width – 10 ns)
• Resolution Up to 6 digits, limited to 100 ps
• Accuracy ±(0.5% of setting +500 ps)
• DUTY CYCLE:
• Range 1 to 99%
• Resolution 3 digits (0.1%)
• Accuracy Limited by width and pulse accuracy
• OUTPUT CHARACTERISTICS:
• AMPLITUDE: 
• High Level Range: -9.90 V to +10 V into 50 Ω load (-19.80 V to +20 V into open circuit)
• Low Level Range: -10 V to +9.90 V into 50 Ω load (-20 V to +19.80 V into open circuit)
• Amplitude Range: 0.1 V to 10 V p-p into 50 Ω load (20 V p-p max into open circuit)
• Resolution: 3 digits limited to 10 mV
• Accuracy: ±1% of setting ±10 mV into 50 Ω
• Aberrations: <5% + 20 mV into 50 Ω load, for pulse levels between ±5V
• Output Resistance: 50 Ω
• Offset Accuracy: ±1% ±25 mV
• OPERATING MODES:
• Continuous: Output continuous at programmed period rate
• Triggered: Output quiescent until triggered by an internal, external, GPIB
• or manual trigger, then generates one cycle at programmed period rate
• Gated: Same as triggered mode except pulses are output for the duration of the gated signal. The last cycle started is completed
• Burst: Same as triggered mode for programmed number of cycles from 2 to 999,999 as set by the N-BURST function
• External Width: Trigger duration and rate sets pulse width and repetition
• PULSE FUNCTIONS:
• Single: One pulse at each selected period up to 50 MHz repetition rate
• Double: One pair of pulses at each period up to 25 MHz repetition rate. Both pulses have the same selected width; the position of the second pulse set by the delay control.
• Range: <6 ns to 100 ms variable. Leading and trailing edges settable separately and limited to 20:1 ratio between settings into one of the following ranges: 5 ns-100 ns; 50 ns-1.0 us; 500 ns-10 us; 5.0 us-100 us; 50 us-1.0 ms; 500 us-10 ms, 5 ms – 100 ms
• Resolution; 3 digits limited to 10 ps
• Accuracy: ±(5% of setting +2 ns)
• Linearity: <5% deviation from a straight line between 10% and 90% points, for transitions > 50 ns
• TRANSITION TIMES:
• Range: <6 ns to 100 ms variable. Leading and trailing edges settable separately and limited to 20:1 ratio between settings into one of  the following ranges: 5 ns-100 ns; 50 ns-1.0 us; 500 ns-10 us; 5.0 us-100 us; 50 us-1.0 ms; 500 us-10 ms, 5 ms – 100 ms
• Resolution: 3 digits limited to 10 ps
• Accuracy: ±(5% of setting +2 ns)
• Linearity: <5% deviation from a straight line between 10% and 90% points, for transitions > 50 ns
• INTERNAL TRIGGER:
• Range: 100 ns to 100 s
• Resolution: 4 digits limited to 100 ns
• Accuracy: ±0.01%
• INPUT AND OUTPUT:
• TRIGGER INPUT:
• Sensitivity: 200 mVpp minimum
• Minimum Width: 10 ns
• Maximum Rate: 50 MHz
• Input Impedance: 10 kΩ
• Input Protection: ±15V DC plus peak AC
• Range Selectable: from -10 V to +10 V
• Resolution: 3 digits limited to 10 mV
• Slope Selection: Positive or Negative
• SYNC OUTPUT:
• A TTL level pulse at the programmed period. Output impedance is 50 Ω, protected against short circuit and up to ±15 V accidental input. The high level is >2 V into 50 Ω and with 3.5 ns typical transition times
• REMOTE PROGRAMMING:
• Interface: GPIB and RS-232, IEEE-488.2 and SCPI compatible
• GPIB Function Codes: SH1, AH1, T6, L4, SR1, RL1, PP0, DC1,DT1, C0, E2
• GENERAL:
• Memory: Non-volatile, stores up to 99 complete panel settings. Last user setup also retained at power down.
• Power Requirements: 100-240 V, ±10%, 48-66 Hz, 50 VA maximum
• Dimensions WxHxD: 8.4 x 11.8 x 3.5 inches (213 x 300 x 88 mm)
• Net Weight: 6.61 lbs (3 kg)
• EMC: Conforms to EN55011 class B for radiated and conducted emissions
• Electrical Discharge Immunity: Conforms to EN55082
• Safety Specifications: Conforms to EN61010, CE Approved
• Operating Temperature: 32 °F to 122 ° F (0 °C to 50 °C)
• Storage Temperature: -4 ° F to 140 °F (-20 °C to 60 °C)
• Humidity: 90% RH at 32 °F to 86 °F (0 °C to 30 °C
• Included accessories : AC Power cord, CD containing instruction manual, RS-232 cable, test report and certificate of calibration

• (1) 4034 - Dual-Channel Pulse Generator 
• (1) RS-232 Cable
• (1) AC Power Cord
• (1) Certificate of Calibration
• (1) Test Report
• (1) User Manual

Brochure/Datasheet

Instruction Manual

Download

Note: Prices are not binding at any time subject to change without prior notice