• The first cost effective ultrasonic solution available on the market.
• Visually compare the unloaded to the loaded waveform.
• Display Options - RF, Rectified, Large Digits with Limits Bar.
• Effectively monitor your bolts during periodic shutdowns over the service life of the fastener.
• Measurement quanities - Time (nanoseconds), Elongation, Load, Stress, and %Strain.
• Display Resolution - 1/8" VGA 240 x 160 pixels.
• Stores 8000 readings and waveforms in multiple groups.
• Built-in Linear regression or vector for optimizing load measurements.
• The Auto Set feature automatically optimizes detection and adjusts display.
• Hi/Lo alarm tolerance limits work in conjunction with the data port and external pump shut-off device.
• IP 65 Rated

• Measuring Range: From 1" to 48" (25.4mm to 122cm) bolts
• Time: Nanoseconds
• Elongation: Change in length (inches/millimeters)
• Load: Force load applied (pounds kIP or kN Killonewtons)
• Stress: Force for unit area stress applied (pounds kPSI or megapascals MPa)
• Strain %: percentage strain applied (inches per inch or millimeters per millimeter)
• Resolution: +/- .00001 inches (0.0001 mm)
• Velocity Range: .0492 to .3936 in/ms; 1250 to 9999 meters/sec.
• Calibration: Fixed, Single, and Two point zero calibration options. Select bolt material types from a preset or custom list.
• Units: English & Metric / Fahrenheit & Centigrade
• Measuring Modes: Pulse-Echo (standard); Pulse-Echo w/Gate (fine adjust)
• Pulser: Square wave pulser with adjustable pulse width (spike, thin, wide)
• Receiver: Manual or Auto Set gain control with 40dB range
• Timing: 10 bit 250 MHz digitizer
• Display Modes: A-Scan - Rectified +/- (half wave view), or RF (full waveform view)
• Alarm Limits: Set hi and lo tolerances with audible beeper, viewable scan bar, and visual LEDs
• Data Logger (Internal): Total of 8,000 readings, multiple bolt groups. Stores both waveform views, nanoseconds, elongation, load, stress, and strain for each reading
• Memory: 4gb
• Transducer: Single Element (1 to 10 MHz & 1/8" to 1" diameters)
• Transducer Cable Length: 10 foot (custom lengths available, inquire)
• Temperature Probe: for automatic temperature compensation
• Setup Memory: 64 custom user defined setups. Factory setups can also be edited by the user
• Gate: Gate used to fine adjust where the detection point occurs
• Auto Set: Locates the detection signal, optimizes the gain setting, and adjusts the overall display to show the waveform and detection point automatically
• Field Calibration: Vector & linear regression. Includes Factory calibration traceable to national standards
• Power: Three 1.5V alkaline or 1.2V NiCad AA cells. Typically operates for 150 hours on alkaline and 100 hours on NiCad (charger not included.)
• Dimensions: Width (2.5in/63.5 mm); Height (6.5 in/165 mm); Depth (1.24 in/31.5 mm)
• Weight: 13.5 ounces (with batteries)
• Operating Temperature: 14 to 140F (-10C to 60C)

• (1) TI-MINIMAX-C v2 
• (3) 3 AA Batteries
• (1) 4 oz. Bottle of Couplant
• (1) USB Type A to Type C Transfer Cable
• (1) Carrying Case
• (1) 10’ Lemo to Microdot Transducer cable
• (1) PC Utility Software (download from website)
• (1) Operation Manual and Certification.
• NOTE: Probes/Transducers and Calibration blocks are sold separately

Brochure/Datasheet

Instruction Manual

Download

Note: Prices are not binding at any time subject to change without prior notice