• Part Number: TI-CMX-WOP
• Probe: Not included
• Includes NIST Traceable Calibration Certificate
• Large, backlit LCD display retains last reading
• Resolution of 0.0001 inch (0.001 mm) with Selectable units of inch or mm
• Built-in datalogging for 10,000 data values stored in up to 40 batches with 250 values/batch with USB Output
• Scan mode, 100 readings/sec. Probe is slid over a large measuring area, the minimum thickness during the "scan" will be displayed
• Adjustable GAIN (AGC) in 5 steps to fine tune the gauge for use on challenging materials or applications
• Can be used with both Single Element Delay Line and contact transducers (5 to 20MHz)
• LCD shows Thickness Value, Velocity Setting, Gain Setting, Stability & Battery Indicators, Scan Mode, Zero and units
• Operates on two (2) AA Batteries - 45 hours continuous operation
• Calibrate to a sample of known thickness which automatically calculates the optimal acoustic velocity
• Powered by: 120MHz FPGA timing & 100 volt spike pulser
• Measure Modes: Pulse-Echo (P-E), Echo-Echo (E-E), Interface Echo (I-E) and Plastics (PLAS)
• Additional Modes Include Differential (from user-entered "nominal value"), Alarm (user-set Hi/Low Limits) and Velocity Mode
• Optional serial RS-232 or Bluetooth output
• IP 65 Rated for protection even in the toughest field conditions
• CE-Certified

• Range in Steel:
• Pulse-Echo Mode Pit and Flaw detection measures from 0.025 9.999inches (0.63 to 254 millimeters)
• Echo-Echo Mode Thru Paint & coatings measures from 0.100 4.000 inches (2.54 to 102 mm). Range will vary depending on the thickness of the coating.
• Max Coating: 0.100"
• Resolution: .001 inches (0.01mm)
• Velocity Range: .0492 to .3936 in./ms (1250 to 9999 meters/sec)
• Units: Inch or mm
• Measurement Modes: Pulse-Echo (corrosion mode); Pulse-Echo Coating (Corrosion w/o coating); Echo-Echo (thru-paint); Temp Comp (auto adjust for material temp); Coating Only (Ultrasonic Coating Gauge)
• Transducer Types: Dual Element (1 to 10 MHz).
• Output: RS-232 for upload/download of setups
• Memory capacity: TI-CMX None; TI-CMXDL over 200,000 measurements
• Power Source: Three 1.5V alkaline or 1.2V NiCad AA cells
• Battery Life: Typically operates for 150 hours on alkaline and 100 hours on NiCad
• Auto Power off: After 5 minutes of non-use
• Display: 1/8 in. VGA grayscale display 62 x 45.7mm
• Keyboard: Membrane switch with twelve tactile keys
• Case: Extruded aluminum body with nickel-plated aluminum end caps (gasket sealed).
• Operating Temperature: -14° to 140°F (-10° to 60°C)
• Weight, net: 383 grams
• Dimensions: 63.5 W x 165 H x 31.5 D mm
• Warranty: 2 year limited
• Certification: CE Approved, Factory calibration traceable to national standards

• (1) Checkline TI-CMX Ultrasonic Coating and Wall Thickness Gauge
• (1) Probe 4 oz.
• (1) Bottle of coupling fluid
• (2) AA batteries
• (1) NIST Calibration Certificate
• (1) RS-232 cable
• (1) Software
• (1) Operating Manual
• (1) Carrying Case

Brochure/Datasheet

Instruction Manual

Download

Note: Prices are not binding at any time subject to change without prior notice