• Part Number: 2895-220V
• 220VAC Voltage Input
• Test frequency range of 20 Hz to 1 MHz
• AC test signal voltage adjustable up to 2 Vrms
• 3 AC current ranges, selectable via 30 Ω, 50 Ω or 100 Ω internal AC impedance
• 30 Ω setting provides up to 66.7 mArms of drive current, sufficient for larger inductors and transformers
• Built-in DC bias source adjustable from -5V to +5V/-50 mA to +50 mA
• Fast measurement speed up to 13 ms/reading to increase manufacturing throughput
• Adjustable measurement speed for fast readout or better accuracy
• 201-point programmable list sweep function provides ability to sweep frequency, AC and DC bias voltage/current levels
• Auto-level control to maintain measurement signal applied to DUT at a constant level
• Test signal voltage and current monitoring
• BIN comparator function to sort components in up to 10 bin locations
• Handler interface for easy integration with a component handler
• 1 m and 2 m cable compensation
• Transformer test function with optional transformer test fixture TL89T1
• Versatile trigger functionality (internal, external, bus and manual)
• Standard USB, LAN, and GPIB interface for remote control using SCPI commands

• Test Signal Frequency: 
• Range: 20 Hz - 1 MHz
• Minimum resolution: 0.01 Hz
• Accuracy: 0.01 %
• Test Signal Levels:
• AC source (ALC* OFF):
• Voltage Accuracy (10% x set voltage ± 2mV) : 
• Voltage Level: 5 mVrms - 100 mVrms; Resolution:  100 µVrms
• Voltage Level: 100 mVrms - 1 Vrms; Resolution:  1 mVrms
• Voltage Level: 1 Vrms - 2 Vrms; Resolution:  10 mVrms
• Current Accuracy (10 % x set current ± 10 µA):
• Current Range: 166.7 µArms - 66.7 mArms; Impedance: 30 Ω
• Current Range: 100.0 µArms - 40.0 mArms; Impedance: 50 Ω
• Current Range: 50.0 µArms - 20.0 mArms; Impedance: 100 Ω
• AC source (ALC* ON)1:
• Voltage:
  
• Range: 10 mVrms – 1 Vrms
• Accuracy: 6% x set voltage ± 2 mV
• Current:
  
• Range: 100 µArms - 10 mArms
• Accuracy: 6 % x set current ± 10 µA
• DC bias source:
• Voltage:
  
• Range: -5 V to +5 V
• Accuracy: 1 % x set voltage ± 5 mV
• Resolution: 0.01 mV
• Current:
  
• Range: -50 mA to +50 mA
• Accuracy: 1 % x set current ± 50 µA
• Resolution: 0. 1 µA
• *Auto Level Control
  
• 1: Resolution and impedance see AC source (ALC OFF) specification
• Measurements:
  
• Measurement parameters: L, C, R, G, X, Z, Y, B, θ, Q, D, DCR
• Transformer measurement parameters2: L2A, L2B, N, 1/N, M
• Basic accuracy: 0.05 %
• AC source Output impedance (± 2%): 30 Ω, 50 Ω, 100 Ω
• Typical measurement time (≥10 kHz) (excluding display refresh time):
  
• Fast: 13 ms / measurement
  
• Medium: 67 ms / measurement
• Slow: 187 ms / measurement
• Equivalent circuit: Series, Parallel
  
• Range mode: Auto, Hold
• Averaging: 1-255 measurements
• Correction function: Open, Short and Load correction
• Cable length compensation: 0, & 1 meter
  
• Math operations: Direct reading, ∆ABS, ∆%
• Trigger mode: Internal, Manual, External, Bus
• Delay time setup: Time from trigger to start: 0 to 60 seconds; Resolution: 1 ms
• Comparator (Bin sorting):
  
• 10-bin sorting, primary bins BIN1-BIN9 and OUT, secondary bin AUX
• Bin counter: 0 to 999,999
• PASS/FAIL indication via front panel LED or handler interface signal
• List sweep:
• 201 sweep points: Sweep test frequency, test signal AC voltage, test signal AC current, test signal DC bias voltage and test signal DC bias current
  
• Measurement parameters: Primary and secondary
  
• Sweep modes: Linear or logarithmic
• Trigger mode: Sequential and Step
• Comparator: One pair of lower and upper limits for primary or secondary parameter (user selectable)
  
• Internal non-volatile memory: Save / recall 40 setups
  
• General:
  
• External USB memory: Save / recall setups, screenshots, measurements and sweep data logs
• Remote interface: USB (USBTMC or virtual COM), RS232, LAN,
• GPIB (895 only)
• Handler interface: 36-pin connector
• AC input: Voltage: 110/220 VAC ±10%; Frequency: 47 – 63 Hz
• Power consumption: Max. 80 VA
• Operating temperature: 0 °C to 40 °C
• Storage temperature: -10 °C to 70 °C
• Relative humidity Up to 80%
• Display: 4.3” TFT color display
• Dimensions (WxHxD): without bezel: 280 mm × 88 mm × 370 mm  (11.02“ x 3.46” x 14.56”) with bezel: 369 mm × 108 mm × 408 mm  (14.52” x 4.25” x 16.06”)
• Weight: 5 kg (11 lbs)
• Safety: EN61010-1:2001, EU Low Voltage Directive 2006/95/EC
• Electromagnetic Compatibility: Meets EMC Directive 2004/108/EC, EN61326-1:2006

• (1) 895 - Benchtop LCR Meter
  
• (1) AC Power Cord
• (1) Set of Kelvin Clips Test Leads for 4-Wire Measurements (TL89K1)
• (1) 4-terminal Test Fixture (TL89F2)
• (1) Brass Shorting Bar (TLBSB)
• (1) Certificate of Calibration
• (1) Test Report

Brochure/Datasheet

Instruction Manual

LabVIEW 2016 Drivers, Ver. 1.0

---

Note: Prices are not binding at any time subject to change without prior notice